Відео

It’s been a while. And I wasn’t sure it was going to finish a couple of times.

Ahh. That makes sense.

Glad to be of service!

I don’t remember any screw troubles, have you tried using a different size of screw? You might have better luck.

I’ll try that but I thought the FM screw was the largest of all screws that come with it? I’ll look. Thank you!

@mikehellrung4992 good luck! If that doesn’t work, perhaps a little glue in the screw hole will give it something to bind against.

@@GrossModelsgreat idea! Thanks, Friend!

I think so. I believe I have the start of the frame to do next.

Yep

It’s getting bigger each pack!

It does not come with a tiny pair of sandals, no. :-)

Not too close either. :-)

Just as well, there’s no room for hands inside!

It’s a good chance. My eyes aren’t great right now and I could easily have got it flipped. Thanks.

👀👀well spotted think you are correct.

It’s entirely possible. I will have a look when I get it back out of its box. Thanks!

None of the fingers properly attach until the front and the back of the hand go together.

@@GrossModels 👍👍

Ta.

Looking forward to the more recognisable bits.

There will be, I’m not sure how much though.

I still might!

Thanks. I started with one stage per video to make it easier to manage, and to be absolutely honest to create more content! Some stages are bigger than others and although many are quite quick I could easily end up with 4 issues being an hour long video on occasion and I’d rather keep to one format rather than having a month of individuals then a month of 4 in 1. I am always looking at my content and trying to improve, so will keep it in mind though!

I appreciate your reply. I definitely understand trying to create content on this platform can be challenging. As a former content creator I get it. Take care and God bless.

I have, and it’s fine. Did you have the nacelles on? They do counterbalance it a lot. Im not sure how long it would stay upright unsupported though.

@@GrossModels yes I put them on but did not click them completely in

@darrenmorgan2617 same. I doubt they will be easy to remove. Did you have the legs out fully and the model all the way down the stand shaft?

@@GrossModels yes think so I will have another go tomorrow

It’s lovely. Thanks!

Indeed it is.

Nice!😮

I believe there are 80 issues planned.

@@GrossModels ok thanks! I’m on the same issues as you so about half way through

Take it slow and steady. Enjoy the build. Hopefully you won’t have a 2 year gap in the middle like I did!

Thanks, I think other things were planned, like the ‘buttons’ all over the build that do not connect to anything. I believe Fanhome are expanding to other areas all the time, I hope they get to you!

It is nice, if a little big!

Thanks for the tip, but it’s a little late! I’ve already finished the next issues. Didn’t have too much trouble, although I doubt I’ll be taking it apart again!

You did better than me then, took me ages!!

@tonysandell9191 as long as you got there in the end!

I’ve already built and filmed that stage! Wasn’t too bad, although the fit was very tight.

The wait for the last pack will seem very long I’m sure.

Although the console versions are no longer supported, I believe everything is still in much the same places. A site like Inara.cz should still be able to guide you to the right area to get stuff. Good luck CMDR o7

It does? That should make life easier! Thanks.

Me neither, but I also wouldn’t have come up with the cathode ray tube…..

No secret, I just pushed. I even took it off again to get into sort the battle section lights out and put it back on again. You might not have the panels done up tight enough? If it’s not almost right as it slides on? I only needed extreme pressure for the last little bit.

Another one to come soon!

The videos are in the playlist, they just haven’t been released yet! In face, one more just released this morning, the other 3 come out Tuesday, Thursday and Saturday.

Not a surprise it’s similar really.